Product Description:
DC motor is a rotating motor that can change DC electric powered energy into mechanical energy (DC motor) or mechanical power into DC electrical strength (DC generator). It is a motor that can change DC and mechanical energy into one yet another. When it operates as a motor, it is a immediate present motor, which converts electrical power into mechanical power when it operates as a generator, it is a direct present generator, which converts mechanical vitality into electrical strength.
| Product Identify | 400V 550V 660V 750V dc motor |
| Motor Type | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition composition | The construction of DC motor ought to consist of two elements: stator and rotor. The static component of DC motor is called stator. The main purpose of stator is to produce magnetic field, which is composed of foundation, primary magnetic pole, commutation pole, conclude cap, bearing and brush gadget. Operating part is referred to as rotor, whose main function is to create electromagnetic torque and inductive electromotive power. It is the hub of energy conversion of DC motor. So it is also frequently named armature, which is composed of rotor, armature core, armature winding, commutator and admirer. |
| Product | ZSN,ZTP,Z4,Z2 |
| Functioning speed | Constant Speed /Reduced Velocity /Change Velocity /Large Speed Other |
| Principal classification | DC Motor is a equipment that converts mechanical vitality into DC electrical power. It is mostly used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation electrical power supply of alternator. Even though in areas in which DC electrical power is required, AC electricity rectifier is also used to convert AC into DC electricity, but from some factors of efficiency, AC rectifier electrical power provide can not fully substitute DC generator. |
| Safety quality | IP55 |
| Thermal Class | a hundred and fifty five (F) |
| Software | DC motors are widely utilised in tape recorders, video recorders, video discs, electrical shavers, hair dryers, digital watches, toys and so on. |
| Maintenance approach | Professional motor upkeep centre motor upkeep procedure: cleansing stator and rotor – changing carbon brush or other components – vacuum F stress dipping paint – drying – Calibration equilibrium. 1. Use atmosphere must be always dry, motor surface ought to be kept clear, air intake must not be hindered by dust, fibers and other obstructions. 2. When the thermal security of the motor carries on to function, it should be ascertained whether or not the fault comes from the motor or the overload or the environment benefit of the protecting device is way too low. After reducing the fault, it can be set into operation. three, make certain that the motor is well lubricated throughout operation. The basic motor runs for about 5000 hrs, that is to say, lubricating grease should be extra or replaced. When bearing overheating or lubricating deterioration is identified in operation, the hydraulic pressure should change lubricating grease in time. When changing grease, the previous grease should be eliminated, and the oil groove of bearing and bearing protect must be washed with gasoline. Then ZL-3 lithium grease need to be filled with one/two (two poles) and 2/three (4 poles, six poles and 8 poles) of the cavity in between the inner and outer rings of the bearing. 4. When the daily life of the bearing is above, the vibration and sound of the motor will enhance naturally. When the radial clearance of the bearing reaches the subsequent benefit, the bearing must be changed. 5, when eliminating the motor, it is Ok to remove the rotor from the shaft extension or the non extension stop. If it is not essential to unload the supporter, it is a lot more convenient to just take out the rotor from the non-axle extension end. When pulling out the rotor from the stator, the stator winding or insulation must be prevented from being broken. 6. When replacing the windings, the type, measurement, turns and gauges of the unique windings should be recorded. When these info are misplaced, they should be received from the maker and the first designed windings need to be changed at will, which often deteriorates a single or many functionality of the motor or even helps make it extremely hard to use them. |
